If you're stuck with your vehicle, double-lining your winch is the answer. You can use this technique to shift heavy stuff or double the amount of pulling power that a single winch can handle. Make sure that the anchor point is strong enough to withstand the additional power from the winch. Therefore, learning how to double winch pulling power is crucial if you are a frequent off-road traveller.
When using a winch, the cable must be at a right angle to the winch drum. If the cable is at an angle, the winch will not pull at full capacity. To prevent this, make sure that the cable is perpendicular to the ground.
As a frequent off-roader or merely an enthusiast, you can learn the tricks of doubling your winch pulling power.
Preparations Before You Start Winch Pulling
You have many necessary steps to take before you can begin winch pulling:
- Make sure that you have an adequate braking system installed. This is important to avoid injury if you are inadvertently lifting something heavy.
- You need to spool the cable properly. The cable must be wound evenly around the drum.
- You can drive your vehicle slowly while the cable is under tension.
Once you are prepared, you need to ensure the straight pull and single line wrap of the winch string around the drum if increasing the pulling strength of your winch is your bet.
The Straight Pull
The Straight Pull is very useful for recovering a rolled-over vehicle. The winch line is the only part of the winch between the truck and the outside world. The pulling force is applied at 90 degrees to the truck. If the line is pulled sideways, the vehicle will turn. If the line is pulled straight, the truck will not go sideways. The straight pull is very important for recovery situations.
Single Line Wrap
Using a Single Line Wrap while winch pulling reduces the risk of a tangled rope. To reduce the chance of a line coming off the drum, make sure that there are no loose wires on the drum. To prevent this, simply remove one wrap and reduce the tail tension.
When handling the line, ensure that you keep your hand away from the drum and pull upwards in a counterclockwise motion. While pulling, you should ensure that the tail runs freely. This way, the line is less likely to come off the drum when you're pulling.
Steps To Double Your Winch Pulling Power
If you want to double your winch pulling power, the best thing to do is use a straight-line winch rigging techniques. This involves wrapping the line around two snatch blocks placed near the anchor point. Just remember that the total force is only on the line that you're pulling.
However, you must remember to use a rock-solid anchor for the snatch block. With the help of a snatch block, you can also make your snatch block more efficient and extend the line to double its power. Here go with the three-step trick on how to double pulling power of a winch.
Step 1: Setting The Strap Around the Tree
As you survey your car in the mud, it may seem like nothing can be done. Thankfully, there's a way to get unstuck without any help from a tow truck. Two separate straps can thread through the tree trunk, one on each side of the vehicle. The strap then wraps around a convenient trunk and is pulled tightly to secure it in place.
A cable attaches the strap on one side of the vehicle and wound onto a winch on the other side. The cable is tightened with a ratchet, drawing the vehicle's stuck wheels in toward the tree, straightening out its stance.
Step 2: Set the Snatch Block
A snatch block is usually needed when pulling a vehicle out of deep snow, mud-stuck situation. A winching snatch block is a pulley block that attaches to a vehicle's winch cable. They are often used on one side of the vehicle and can be used as a temporary solution to pull on steeper inclines from the stranded or stuck condition. They are handy when you need to pull your stranded vehicle out of a ditch, off an embankment, or up a steep incline.
Step 3: How to Hookup the Snatch Block
The location and type of materials needed to set up a snatch block will depend on where the vehicle becomes stuck. Winching is an excellent way to pull your stranded vehicle out of tough spots if you're using the right equipment and power.
Snatch block becomes the call of the situation when you want your rescue tool to employ more power than it is designed to – double the pulling power it offers normally. If you know how and where to grab a snatch block when winching your stranded vehicle, the rest is just pulling with the pulling power multiplied.
They should attach the double snatch block to the vehicle's frame below the stuck tire at an angle of 45°. Their other arm should be outside and holding onto the second rope while their body is inside and pulling on the first rope.
Note: You Can Also Learn In-Depth Snatch Block Using Guide Here: automobilenote.com/how-to-use-a-winch-pulley-block/
How do you Increase the Speed of the Winch? Can it help?
When a vehicle becomes stuck, either snow or mud can impede the vehicle's progress. We already have learned that doubling winch pulling strength is urgent in this regard. Now, the question is, "Will the increase of winch pulling speed help in this situation?" Increasing pulling power is not always the answer. It may decrease the time it takes to pull a stuck vehicle out of whatever trouble it has found itself in.
Increasing the winching speed can help when towing a stuck vehicle; you want to make sure that the tow strap is carefully connected to the stuck vehicle's hitch. Make sure that your winch has enough (double) power when pulling your car out of its predicament.
Wrap Up
If you're looking for ways to double your winching performance, this article may be helpful. With more pulling power, the winch makes your work easier.
If you want to double your winching power, follow the instruction shared here.
You can come across several tricks and tips on the process of doubling your winch rescue power. But this process has to remain central.
Also Read: